Loading... Please wait...

Azteeg X5 mini 32BIT All-in-one Controller V1.1 - Screw Terminals

Hover over image to zoom

  • Image 1
  • Image 2

 Product Description

Azteeg X5 mini 32BIT All-in-one Controller V1.1 - Screw Terminals

The X5 mini is a 32 bit ARM based Motion controller for 3D printers, CNC Machines and Laser cutters. The X5 mini runs on Smoothieware firmware and is based on Smoothieboard by the awesome Arthur Wolf. The X5 mini uses the powerful 32bit, 120Mhz NXP LPC1769 ARM chip capable of faster calculations for faster and smoother movements without breaking a sweat. 

Configuration is easier using a text based config file loaded on the SD card, no need to upload firmware every time you make a change. Just edit the config file from your PC then reboot the board with the new config and you're done.

Compact and powerful all in one solution. Board size: 3.4"(94mm) X 2"(50mm)

Consider using our GLCD to Azteeg X5 Mini Connector Board if you're using a GLCD.

Changes from v1.0

  • Solder jumpers for fast decay mode ( stepper drivers)
  • Added/changed expansion pins
  • Improved ESD protection on USB lines
  • Replaced USB receptacle( Through hole)
  • Break out pins for onboard SD slot, play and reset functions.
  • Direct plug-in expansion for mini Viki and Viki 2.0 Graphic LCDs. 
  • New PCB color ( Deep Brown)
  • 32BIT NPC LPC1769 120MHZ ARM processor.
  • Compatible with Smoothieware firmeware by Arthur Wolf
  • 4 Built-in DRV8825 1/32 msteps stepper drivers
  • Digital pot stepper driver current control
  • 1 High Current Mosfet for Heat bed control
  • 1 Mosfet for Hotend control
  • 1 FAN Mosfet
  • 4 end stops and 2 thermistor inputs
  • Wide input high efficiency switching Power supply (5v @ 1A max)
  • Micro SD card slot built in
  • High current Terminal blocks can Handle up to 20 Amps per pin
  • RoHS, 4 Layer, 2oz per layer PCB
  • Comes with Heatsink strip for better heat dissipation at higher currents
  • ESD/Surge protected endstop inputs
What's in the box:
  1. Azteeg X5 mini controller board with Bootloader
  2. Heatsink strip
  3. Shunt jumpers


NOTE: Micro SD card pictured is not included.

 Find Similar Products by Category

 Product Reviews

  1. Great Controller

    Posted by Matt W. on 11th Feb 2016

    I received this with my UltiBots Kossel 250 V-Slot BSE as a substitute for the one with pin terminals which were on back-order. The controller is excellent quality. All movements on the BSE are smooth and fluid.

    I used pins from a pin header (thanks to the UltiBots FAQ for this suggestion) so I didn't have to remove the connectors on my steppers and other electronics. I may eventually remove the connectors and fully utilize the screw terminals mainly to reduce the amount of excess wires.

    I was having some issues with Pronterface when performing calibrations. The delta carriages were slamming against the endstops. A quick internet search indicated that the mounted drive for the SD card was the culprit. If you connect this to your computer using the USB then make sure you eject the external SD drive before you control the board using any other software.

  2. Nice controller

    Posted by Kevin on 21st May 2015

    Received the X5 quickly after ordering. Support from Ultibots has been great, as usual. I've tested so far and will be installing into a deltabot. Looking forward to a way to connect to GLCD easily. I like the 1/32 stepping option and compact size.

You Recently Viewed...


Follow us on

Copyright 2017 UltiBots LLC. All Rights Reserved.
Sitemap |

Click the button below to add the Azteeg X5 mini 32BIT All-in-one Controller V1.1 - Screw Terminals to your wish list.